The quick read
  • Screens add light to make color (RGB), presses subtract light with ink (CMYK), and a spot ink is one color mixed ahead of time. A print never matches a monitor exactly because the two systems start from opposite physics.
  • Some bright screen colors fall outside what four process inks can reach, so convert on purpose, look at the result, and fix what shifted before you send the file.
  • Choose by job: process for photos, a named spot ink for a brand color that must not drift, and a clear spec table so every vendor makes the same call.
  • Paper, finish and lighting change what you see. Approve color on the stock you ordered, under neutral light, and expect small variation between runs.

Why print never matches the screen

Here is the situation almost every designer meets sooner or later. You spend two days on a layout. The teal on your monitor is electric, the orange next to it practically hums, and the file goes to press. A week later a box arrives and the teal is calmer, the orange is a shade deeper, and someone in the room says the printer got it wrong.

Usually the printer did not get it wrong. Two machines that make color in opposite ways were asked to show the same thing, and they did the best each could. Your monitor is a light source. It sends red, green and blue light straight into your eyes. A printed sheet is not a light source at all. It sits there reflecting whatever light falls on it, and the ink only decides how much of that light gets bounced back. A glowing surface and a reflecting surface will never look identical, even when the numbers are close.

That one fact explains most of the arguments about color in print. There are a few more layers on top of it, and this article takes them one at a time:

  • The range of colors each system can physically produce is different, and print's range is smaller in places.
  • The same numbers look different on different screens, and different again on different paper.
  • Finishes, coatings and the light in the room all shift what you perceive.
  • Every press has a little natural variation from one run to the next.

None of this is a reason to give up on accurate color. It is a reason to stop treating the screen as the final judge. Treat it as a draft, and bring in the right tools when color matters: a profile, a proof, and sometimes a dedicated ink.

This piece is written for designers who send files to press, for brand managers who inherit those files, and for resellers who relay artwork from clients and take the blame when a box looks off. It stays practical. You will find how each system works, how to set up a document, how to convert, how to document a brand color, how to proof, and what to do when something still looks wrong. Where numbers appear, they are labelled as illustrations, because no honest article can promise that a specific value prints a specific way. Press, paper and ink all have a say.

If you only remember one thing, make it this: the screen shows you intent, and the press delivers a negotiated result. Your job is to make that negotiation happen before the run, on purpose, rather than after the boxes arrive.

ScreenPrinted sheetLightMakes its ownReflects room lightMixingAdds lightSubtracts lightBrightestFull light outputBare paperDarkestLight switched offHeavy ink coverageJudged byDisplay and settingsPaper and lighting
A screen emits light directly while a printed sheet only reflects the light that falls on it.

The three systems you will actually use

Three color systems cover nearly every printed job. RGB describes color made of light, and it is what your design tool, camera and monitor speak. CMYK describes color built from four inks, cyan, magenta, yellow and black, which is how most full color printing works. Spot color describes a single ink mixed ahead of time to a specific recipe and put on the paper as is.

A printed piece often mixes them. A brochure can carry photos in four color process, a logo in one spot ink, and a glossy highlight added as a coating. The skill is knowing which color on the page is doing which job, and which system should carry it.

How screens make color

A screen is a grid of tiny light sources, each built from three sub-parts: one red, one green and one blue. Your eye sits far enough back that it cannot resolve them, so it blends their light into one color. Nothing is mixed on the glass. The mixing happens in your visual system.

Additive color, in plain terms

This is called additive color because adding light makes things brighter. Turn all three channels to zero and the pixel emits nothing, which reads as black. Push all three to full and you get white. Red and green together read as yellow. Green and blue together read as a cyan-like blue. Red and blue together read as magenta. Those overlaps matter, because they are the doorway to understanding CMYK: the secondary colors of light are the primary colors of ink.

Each channel in a typical design file holds 256 steps from none to full, so a file has a very large number of possible combinations. That sounds like unlimited range, but a number alone does not say which red you are asking for. That depends on the color space.

Red lightGreenlightBlue lightAllthree:white
Overlapping red, green and blue light produces the secondary colors and, at full strength, white.

Color spaces and gamut

A color space is a defined set of reds, greens and blues plus a rule for how the numbers map to actual light. The most common one for the web and for ordinary displays is sRGB. It is a modest space, designed so that a wide range of ordinary screens would look roughly alike. Wider spaces exist. Many modern displays and cameras can show or record more saturated greens, reds and blues than sRGB allows.

The range of colors a space can hold is its gamut. A bigger gamut means more vivid extremes are possible. That sounds purely good, and for screens it mostly is. For print it is a trap, because a wide gamut file contains colors that no press can reproduce. A saturated green that looks wonderful on a wide display can only be printed as a near neighbour.

What can go wrong on the screen itself

Even before print enters the picture, your screen is a variable.

  • Brightness. A display turned up high makes everything look punchier, and dark areas look lighter than they will in print.
  • Calibration. An uncalibrated screen can lean warm or cool, and two monitors on the same desk can disagree.
  • Profile. If the operating system does not know what your display really does, it cannot correct for it. A profiled, calibrated display tells the truth about the file more often.
  • Ambient light. A bright window behind you or a warm lamp beside the screen changes how colors read.

For casual work, none of this matters much. For brand color, packaging, or anything a client will compare against an older print, it matters a lot. A calibrated display, set to a moderate brightness in a dim, neutral room, is the cheapest upgrade to color judgment you can buy.

How presses make color

A press starts with paper that reflects most of the light that hits it. Ink goes on top, and each layer of ink absorbs some of the light before it can bounce back. More ink absorbs more light, so the surface gets darker. This is subtractive color, the opposite of a screen. White is the paper itself, not a color you can add.

Process color and the four inks

Most full color printing uses four inks: cyan, magenta, yellow and black. Cyan absorbs red light and reflects blue and green. Magenta absorbs green. Yellow absorbs blue. Layer cyan and yellow and you get a green, because the pair absorbs red and blue and lets green through. Layer all three and you approach a dark neutral, but not a convincing black, which is why the black ink exists. The K in CMYK stands for key, historically the plate that carried the detail that other colors registered to.

The inks are translucent, not opaque. That is key. A yellow layer lets the paper and any ink below show through, so the order, the paper and the amount of ink all change the result.

Halftone dots and screening

A press cannot lay down a thin film of one ink in a thousand strengths. It prints dots. Each of the four inks is printed as a pattern of tiny dots, and the size of the dots, not the density of the ink, sets how strong the color looks. Small dots with plenty of paper between them read as a pale tint. Large dots that nearly touch read as a deep tone. Your eye blends the dots and the paper into a continuous shade, the same way it blends screen pixels.

The four dot patterns are laid at different angles so they do not pile into obvious lines. Where the angles interact, you get a small flower-like pattern called a rosette. Under a loupe, a printed photo is a field of these rosettes. At normal reading distance the structure vanishes. At the edge of the pattern, in fine detail, it can show up as a faint texture, which is one reason very fine screens and high quality paper pair well.

1File valueA percent of each ink2ScreeningPercent becomes dot size3Plates or imagingOne layer per ink4Ink on paperDots overlap and blend5Eye blendsReads as a smooth tone
Each press color starts as a percentage in the file and ends as a pattern of dots on paper.

Dot gain, the quiet darkening

When a dot of wet ink lands on paper, it spreads a little. Uncoated paper soaks ink sideways like a blotter, so dots grow more. Coated paper holds the ink up, so dots grow less. This growth is called dot gain. A midtone that your file says is a fifty percent dot may print as if it were a good deal heavier. The effect is largest in the midtones, which is why photos on uncoated stock often look darker and denser than the screen version.

Presses and software are built to expect this. A color profile for a given press and paper describes the typical gain, and converting through that profile pre-compensates so the printed result lands close to the intent. Skipping the profile does not remove dot gain. It just means nobody corrected for it.

Viewing lightFalls on the sheetInk layersAbsorb part of the lightCoating or varnishChanges surface shinePaper surfaceReflects the rest
Light passes through translucent ink layers, bounces off the paper and comes back already filtered.

Why this matters for how you work

Because ink is subtractive, translucent and spread by the paper, the same file never prints the same way on two stocks. Your decisions about paper, finish, profile and proof are really color decisions. That is why the rest of this guide spends so long on them.

Gamut: the colors print cannot reach

Put the range of colors a typical screen can show next to the range four process inks can print, and the screen wins in several places. Not everywhere. Print can reach some deep, dark cyans and certain yellows that a screen has trouble matching. But the saturated blues, vivid greens, electric oranges and neon pinks that make a layout look alive on a monitor are the colors most likely to fall outside the printable range.

Those colors are called out of gamut. When you convert an out of gamut color to CMYK, the software cannot invent ink that does not exist. It finds a printable color it considers closest, according to a rule called rendering intent. The result is usually a duller, slightly darker neighbour. You did not lose the color by mistake. The color was never printable with those inks.

Why blues, greens and oranges suffer most

The reason is physical. Cyan, magenta and yellow inks each absorb a band of light, and none absorbs a band perfectly. Real inks leak a little of the wrong color. When you overlap two inks to build a saturated secondary, the impurities show. A vivid screen blue asks for a very pure, very strong blue, and a magenta and cyan overprint cannot supply it. The mixture lands a bit purple or a bit gray. Greens run into the same limit from the other side.

Fluorescent colors sit entirely outside the process range. A highlighter yellow or a neon pink on a screen is not a color of ink at all, since it glows by converting invisible light into visible light. Process inks cannot do that. Only a special ink can.

Wider spaces, tighter squeeze

If you work in a wide gamut space, the gap to CMYK is larger, and conversion has more to squeeze. The shift can look dramatic when you convert a bright photo for the first time. That is not a bug in the workflow. It is the real cost of printing a saturated image with four ordinary inks, and the right response is to manage it, not to pretend it is absent.

1231Wide gamut displayMost saturated colors2Common screen rangeWhat most monitors show3Process print rangeWhat four inks canreach
Illustration of the idea: the colors a typical press can print are a subset of what a wide display can show.

Seeing the loss before you print

Good design tools let you preview gamut. You can turn on a gamut warning that paints out of range pixels in a flat gray, and you can soft proof with the printer's profile to see the converted look on screen. Use both before you commit. If a logo color is flagged, you have three honest options: accept the nearest printable color, adjust the surrounding colors so the shift looks intentional, or move that color to a spot ink.

Spot colors and named ink libraries

A spot color is one ink, mixed ahead of time, printed from its own plate or its own pass. Where process color builds a hue out of dots of four inks, a spot ink is the hue itself. The press operator opens a can of a specific ink, or mixes one from a published recipe of base inks, and puts it on the sheet at full strength.

That is why spot color is the brand color workhorse. A brand that says its blue is a particular numbered ink is saying something precise. Every printer on earth that has access to that named spot ink library can mix the same color, and the result stays steady from job to job.

Named spot ink libraries

Several libraries of numbered spot inks exist, and printers keep swatch books for them. Each entry has a name or number, a recipe, and a printed chip on a given paper. When you specify one in a file, you pick the entry by its exact name, and the printer prepares that ink. A good habit is to specify the coated or uncoated version of the entry that matches your stock, because the same recipe looks different on each paper, and libraries publish both chips.

On a digital press with a wide color set, a spot entry may be simulated by process inks plus extra colors. The simulation can be very close, but it is a simulation. Ask whether the job will run with true ink or a simulated match, and what that means for color tolerance.

When one ink beats four

Spot color earns its cost in a handful of situations.

  • A brand color that must not drift. The same ink gives the same result across jobs, paper and printers far more reliably than a process mix.
  • A color outside the process range. Deep blues, saturated oranges and bright greens that process cannot hold.
  • A large flat area. A broad solid in process color shows dot structure, banding and variation across the run. A single solid ink is smooth and even.
  • A simple job. A two color business card, black plus one spot ink, can look cleaner and cost less than full process.
  • Special effects. Metallics and fluorescents are inks of their own.

It is the wrong choice for photographs, which need the full range of process dots, and for pieces with many different colors, where each additional spot ink adds a plate or a pass.

Does this color have to be exact andsteady?No, close is fineBuild it inprocess colorYes, and it is a large solidUse a named spotinkYes, and it is part of a photoProcess, thencheck a proof
A short decision path for choosing between process and spot ink for a given color.

The cost trade

On many presses, every spot ink adds something: another plate, another unit, another wash, more setup. On others, especially some digital presses, the extra cost is smaller or built into a fixed color set. The honest answer depends on the press and the quantity, so ask when you quote. For a short run on a flexible press, the cost of one spot ink may be modest. For a long offset run, a single spot ink is often a bargain next to controlling a delicate process mix.

Converting a spot color to process

You may have to. If the budget does not allow a spot ink, or the press cannot run one, the design tool can convert a spot swatch to its nearest process equivalent. The converted color will usually shift, and the reasons from the gamut section apply. Preview it first, and tell whoever owns the brand before the file goes out, not after.

A second meaning of spot

The word has a second life in print files. Finishes such as spot UV, foil and embossing are placed in artwork using a named spot swatch on its own layer. That swatch never prints as an ink. It is a label that tells the finishing step where to act. You will see that in the finishes section, and the premium finishes guide goes deeper: see Foil, Embossing and Spot UV: Premium Finishes.

Tints, overprint and knockout

Once you work with more than one ink, three words come up constantly: tint, overprint and knockout. They are simple ideas that cause a surprising share of press surprises.

Tints

A tint is a lighter version of an ink, made with a smaller dot, not with watered down ink. A fifty percent tint of a spot ink is the same ink printed as a halftone dot pattern covering half the area. The paper shows between the dots, and your eye reads a lighter shade. This is efficient, since one ink gives you a whole family of values. Be aware that very light tints, in the single digit percentages, can break up or vanish on press. Most printers publish a minimum, and the safe move is to stay comfortably above it for anything that must be visible.

Knockout and overprint

Where two colored objects overlap on a page, there are two ways the press can handle the overlap.

With a knockout, the top object removes the ink of whatever is beneath it. A hole is cut in the lower layer exactly the shape of the upper one, and the top ink prints into the hole. The color you see is the pure top color.

With an overprint, the top object prints on top of the lower one without a hole. The two inks stack, and the viewer sees a blend, the way two transparent colored films overlap. A yellow printed over a cyan produces a green.

Most of the time you want knockout, because it gives the color you asked for. Overprint is useful on purpose in a few cases, for instance black text over a colored background, where a knockout would require perfect alignment and any slight shift would show a thin white halo.

1KnockoutTop ink replaces what isbeneath2OverprintInks stack and blend3TrapSmall overlap that hides gaps4MisregistrationPlates drift and show gaps
The same overlap behaves differently depending on how the press is told to treat it.

Trapping, in a paragraph

Plates never line up perfectly. Misregistration, the slight drift between inks, can leave a thin white sliver where two colors meet. Trapping is the practice of letting adjacent colors overlap by a hair so no paper shows. Printers and prepress software usually add trapping automatically for solid areas, so the main thing for you is not to fight it with fine, hard-edged, unoverlapped color joins on thin lines.

Where overprint bites

Accidental overprint is a classic trap. A white object set to overprint on a colored background is invisible on press, because white is not an ink and adding no ink changes nothing. A light colored text set to overprint on a dark image mixes with it and goes muddy. The reverse mistake also happens, with black text knocked out of a color field, which leaves a thin gap if plates drift.

The remedy is plain: check overprint settings before export, use the attributes or separations preview in your design tool to see what will actually print, and treat overprint on anything except black as a deliberate decision. The Inkgility proofer includes an overprint review flag because overprint cannot be verified automatically from a file. More on that later.

Black, rich black and the total ink limit

Black looks like the easy color. It is the one that trips people up most.

Black only, for text and fine lines

The black plate printed alone, with no cyan, magenta or yellow under it, is called K only, or 100K. It is the right choice for body text, captions, thin rules and barcodes. Because only one plate is involved, there is nothing to misregister. Small letters stay crisp, and the press runs it easily.

Rich black, for big solids

A large area of K only can look thin, a little gray, especially next to a dark photograph. Rich black adds some of the other three inks beneath the black to deepen it. The extra inks cool or warm the tone and raise the density. The look is a deeper, more solid black, and it is the standard for big backgrounds, full bleed dark panels and large display type.

Rich black is a recipe, and recipes vary. Here is an illustrative one, to show the shape of the idea and not to copy:

Illustrative rich black recipe (not a promise)

A common pattern is a high K value with modest amounts of the other three inks underneath, for instance something like 60 cyan, 40 magenta, 40 yellow and 100 black. The exact numbers differ by press, paper and personal taste, and a cooler or warmer cast comes from shifting the ratio. Ask your printer for the recipe they prefer. Do not guess. Raising every ink to its maximum does not make a better black, it makes a wet, muddy one that may break the ink limit.

Where rich black goes wrong

Two places. The first is small text. If fine type is set in a rich black, four plates have to line up perfectly to make it. Any slight drift puts colored fringes on the edges, and the letters look fuzzy or soft. Keep small text in K only, and use rich black for large areas and big headlines.

The second is a hidden conversion. A pure black in an RGB file converts to a mix of all four inks, unless the conversion rules say otherwise. Some design tools preserve pure black as K only during conversion and some do not, so it is worth checking black text after any conversion and changing it back if it picked up extra inks.

Registration black

Registration black is a swatch that puts 100 percent of every ink on the page. It exists for crop marks and alignment marks, which need to appear on every plate so each plate can be lined up. Never use it for artwork. It would print every ink at full strength, soak the sheet, and look terrible. If you see it in a file by accident, replace it with a proper black.

Total ink limit

Every press and paper has a maximum amount of ink it can carry before problems start. Stack too much and the ink stays wet, offsets onto the sheet above it in the pile, smears at finishing, or dries slowly enough to delay the job. The sum of all four ink percentages at a point is called the total ink coverage or total area coverage, and printers set a limit for it. A solid pure black at 100K is only 100 percent total. A heavy rich black can be several hundred. The figure printers accept is commonly a few hundred percent, and the number depends heavily on stock and process, so treat any number you read as a conversation starter and ask for the real one.

Uncoated paper is thirstier and more forgiving of wet ink in some ways but spreads it more, so limits are usually lower there. Coated paper holds ink on top and can dry slower in other ways. This is another reason the printer's profile matters: a profile built for the press and paper handles the ink limit for you during conversion.

Low inkHeavy inkLight tintLittle inkK only blackOne plateRich blackFour platesPast thelimitWet, muddy,risky
Illustration of ink coverage from a light screen tint to heavy rich black, with the printer limit somewhere along the way.

Setting up a document correctly

Most color trouble can be avoided in the first ten minutes of a file's life. Here is a setup routine for a print document, in the order that works.

Choose the color mode on purpose

For a piece going to press with a fixed color target, begin in CMYK, or begin in RGB only if you plan a deliberate conversion and know when. A document that mixes modes by accident, with some objects RGB and some CMYK, is the most common source of unexpected shifts. If you start in RGB to keep a wide gamut while you work, write down the conversion step so it is not skipped.

Assign the right profile

An ICC profile is a small data file that describes how a particular device or output turns numbers into color. A document needs a working profile, and an output profile describes the press and paper. Ask your printer which output profile suits the job, and apply it when you convert or export. If you cannot get one, a general purpose coated or uncoated profile for your region is a reasonable fallback, but ask, because the right one improves results more than any other single setting.

Set up swatches, not sampled colors

Build your colors as named swatches. Brand colors, tints, spot inks and the black recipes you use belong in the swatch panel. A swatch is a definition, so changing it updates every object that uses it. A color sampled by eye from an image, or a stray value on a single object, is a trap for the next person to open the file.

Name swatches so their role is clear. A name that includes the target, such as the spot ink's exact name with its coated or uncoated suffix, avoids guesswork later.

Set up bleed, trim and safe zone

Bleed is the extra margin of artwork beyond the cut line, so that a slight shift in trimming never leaves a white edge. Add it to any element that touches the edge. The safe zone is the opposite: an inner margin where text and logos stay, so trimming cannot clip them. Document setup in most tools lets you enter bleed once and shows guides. Whatever the guides say, check the product's own template for the sizes. The templates page has starting files for common products, and the artwork upload checks trim and bleed against the product.

Place images carefully

Linked or embedded photos arrive with their own color modes and profiles. Know what each carries. A photo tagged with a wide gamut profile placed in a CMYK document gets converted on the fly, and the conversion may use defaults. It is safer to convert photos yourself, deliberately, before placing them, or to convert the whole document at the end, and then check.

Fonts and live effects

Convert text to outlines or embed fonts when exporting, so a missing font can never substitute. Keep effects such as drop shadows and transparency in mind, because they flatten during export and sometimes change color. The transparency section explains why.

Export a press ready file

Export to a PDF with the settings your printer specifies, including the output profile, bleed, crop marks if requested, and fonts embedded. Then open the exported file, not the original, and look at it. It is common to find the export dropped a spot color, flattened something, or shifted a gray. Ten seconds of looking beats a reprint.

Color mode chosenCMYK, or planned conversionOutput profile assignedAsk the printerSwatches namedNo sampled stray colorsBleed and safe zone setMatch the product templateFonts outlined or embeddedBefore exportExported PDF reopenedCheck what survived
A new print document should have these items settled before any real design work begins.

Converting RGB to CMYK on purpose

At some point, almost every project crosses from RGB into CMYK. The only question is whether you do it or whether it gets done for you at the last minute, with settings nobody chose. Choose to do it yourself.

When to convert

Convert as late as you can, but before you send the file. Photos edited in RGB keep their full range and edit better there. Once the design is final, convert the whole document, look at the result, and fix what moved. Converting early and editing in CMYK is fine for a project with a tight color target, since you see the real limits while you design. Converting twice, RGB to CMYK to RGB and back, damages color and should be avoided.

Profiles and rendering intent

A conversion needs two things: the source profile, which says what the numbers meant, and the destination profile, which describes the press and paper. Then it needs a rule for what to do with colors the destination cannot hold. That rule is the rendering intent. Two are common for print.

Relative colorimetric keeps in-gamut colors exactly as they are and moves out of gamut colors to the nearest edge. It preserves accuracy where it can. With black point compensation turned on, it also maps the darkest shadows sensibly. Colors that were out of range may flatten into the same value, which loses subtle differences in saturated areas.

Perceptual shrinks the whole range a little so out of gamut colors fit and the relationships between colors stay natural. Everything shifts slightly, even colors that did not need to. It tends to suit photographs with lots of vivid color. Logos and brand colors usually do better with relative colorimetric, since you want the in gamut ones untouched.

There is no universal winner. Preview both on your image, and choose the one that looks closer to your intent.

Rendering intents compared for print conversion
IntentWhat it doesGood forWatch for
Relative colorimetricKeeps in gamut colors, clips the rest to the edgeLogos, brand colors, flat graphicsSaturated areas can flatten
PerceptualCompresses everything a little to fitVivid photographsColors that were fine also shift
SaturationPushes vividnessCharts and business graphics, rarely used in printPoor for brand accuracy

A conversion workflow that works

  1. Confirm the source profile of the file or image, so the numbers mean what you think.
  2. Get the output profile from the printer, or choose the closest standard one for the stock.
  3. Turn on a gamut warning and a soft proof using the destination profile.
  4. Convert with relative colorimetric and black point compensation as a starting point.
  5. Compare to the original. If a photo looks flat, undo and try perceptual.
  6. Fix anything that moved too far, using the repair steps below.
  7. Check black text and thin rules for added inks.
  8. Export, reopen, and compare the exported file to your soft proof.

What usually shifts, and how to fix it

Bright blues move toward purple or navy and lose punch. Greens go olive or lose their glow. Oranges and reds hold up better but can darken. Pale, delicate pastels may lean one way. Deep, rich shadows can plug up.

Repair after conversion, not before, and make changes in the converted file so you are adjusting the real printable color. Raise brightness slightly where the conversion darkened an image. Bring up saturation modestly in the areas that went flat, and watch for the gamut warning to stay quiet. For a brand blue that went purple, nudge the hue back toward your intent with cyan and magenta balance. If no nudge restores it, that color is out of reach, and the next step is a spot ink or an agreed substitute, not more fiddling.

Hypothetical: a vivid teal logo

Say a logo uses a bright teal that the gamut warning flags. After a relative colorimetric conversion, it looks a shade deeper and a touch grayer. The designer has three paths. Accept it and update the guidelines to name the printable version. Add a bit of cyan and trim black until it looks closer, and record the new recipe. Or move the logo to a named spot ink for packaging where it must be exact. All three are fine, depending on cost and importance. What is not fine is leaving the choice to whoever converts the file next. This is a made up scenario to show the reasoning, and it implies nothing about how any particular teal prints.

1Confirm sourceKnow the starting profile2PreviewSoft proof and gamut warning3ConvertChosen intent and profile4RepairFix what shifted5CheckBlack text and ink limit6ExportReopen and compare
A deliberate conversion adds a preview, a decision and a check at each step before export.

Photos, vector logos, gradients and transparency

Different kinds of artwork carry color differently, and each has its own habits on press. Knowing which is which saves arguments.

Photographs

A photograph is a grid of pixels, each with a color value. Its quality for print depends on resolution and on color. On resolution, the usual target is around 300 pixels per inch at the size it will print. Lower still works for large pieces viewed from a distance, but a photo stretched far past its native size turns soft. The Inkgility proofer reads this as effective resolution and flags it, as covered later.

On color, photos are the artwork most affected by conversion, since they contain a continuous range of tones, including the saturated ones that go out of gamut. Treat each important photo as its own conversion decision. Skin tones, product shots with a brand color in them, and food photography deserve a close look on a proof, because viewers know exactly what those should look like.

Vector logos and flat shapes

A vector shape is a mathematical outline filled with a color value. It has no pixels, so it prints sharp at any size. The proofer treats vector artwork as passing the resolution check for that reason. The color of a vector fill is a swatch, which makes it the easiest artwork to control: define the swatch once, and every use matches.

Logos should live as vector files with their color defined as named swatches in each brand mode, one set for screens, one process set, and one spot version where a spot ink exists. If a logo only exists as a raster image, ask for the vector original. Rebuilding it is cheaper than explaining why the edges look soft.

Gradients

Gradients are where print and screen disagree in a very visible way. On a screen, a smooth blend between two colors runs through many fine steps. On press, the blend is built from dot patterns that change size gradually, and a few things can go wrong.

  • Banding. Visible stripes where the tone steps instead of flowing. It shows most on gentle gradients across large areas and on uncoated paper.
  • Light end drop-off. The pale end of a fade falls below the minimum dot a press can hold, so the gradient seems to stop short or end in an abrupt edge.
  • Color cast. A gradient between a saturated color and white or gray can pass through a muddy middle once converted.

To tame them, keep the gradient in the file at full resolution, avoid ending at zero percent of an ink on the edge of a visible area, add a very light noise or texture to break up banding, and choose a conservative range when the brand uses gradients heavily. A proof on the real stock tells you the truth.

Transparency and effects

Drop shadows, glows, blend modes, soft masks and opacity changes all involve transparency. A screen computes the blend in light. A press needs the result as ink, so the file has to be flattened during export, turning live effects into plain objects. Most of the time this goes unnoticed. Sometimes it does not.

  • A shadow on a colored background may pick up a different color than expected, because the blend was calculated in a different color space.
  • A blend mode that looks great in RGB, such as one that brightens or adds, may have no clean CMYK equivalent, and results shift after conversion.
  • Overlapping transparent objects that flatten can create hairline seams, thin lines where flattened pieces meet.
  • Spot colors under transparency may be converted to process during flattening unless the export is told to preserve them.

The safest move is to preview the flattened result: most tools can export a flattened preview, or you can look at the PDF you exported at high zoom. Fix surprises by replacing a live effect with a plain shape, building a shadow as a soft edged image, or changing the blend to normal and adjusting colors by hand.

Which artwork type needs which kind of attention
ArtworkColor riskResolutionWhat to check
PhotographHigh, many tones, some out of gamutNeeds about 300 effective DPIConversion result, skin and brand tones
Vector logoLow, defined by swatchesNot an issueSwatch names, spot versus process
GradientMedium, banding and edge drop-offDepends on typeProof on actual stock
Transparency or effectMedium, changes at flatteningFlattening may rasterizeFlattened preview of the exported PDF
Check on proofProof and convert with careLow worryWatch effectsVector logoPhotographGradientLive shadowPlain textSurprise risk on press →Color control needed →
Artwork sorts by how much color control it needs and how likely it is to surprise you on press.

Paper stock effects on color

Paper is not a neutral background. It is part of the color, since it supplies the white and decides how much light comes back.

Coated and uncoated

A coated sheet has a smooth surface treatment that keeps ink on top and stops it from sinking in. Dots stay sharp, colors look clean, bright and saturated, and photos hold fine detail. The sheet itself reflects light more evenly and comes in gloss, satin or matte versions, which change how the coating handles shine.

An uncoated sheet has an open, fibrous surface that absorbs ink. Dots spread more, colors look softer, flatter and slightly darker, and detail is a little less crisp. Many people prefer the tactile, honest look, and it is the stock for writing on. What you give up is some vividness, so file preparation and profile choice matter even more here.

White point and brightness

Papers have different shades of white. A bright, cool white raises contrast and makes colors look sharper. A warm, creamy white lowers contrast and gives everything a soft glow, while adding a faint yellow cast to light colors. When you use a profile for a particular stock, it accounts for that tone. Without it, a sheet with a cream tint will push all your colors warm.

Kraft, tinted and dark stocks

On a kraft or colored sheet, the paper color shows through the translucent inks. Yellow disappears on a dark brown sheet. Pale tints vanish. Anything that depends on white, such as a white logo on a colored card, simply shows the paper unless white ink is printed. Process inks on a dark sheet look muddier, and the result is closer to a stamp than a photograph.

For colored stock, design with fewer, stronger colors, prefer spot or metallic inks, plan for an opaque white ink wherever white must appear, and ask for a printed sample on the actual sheet. Do not rely on a screen preview, because a screen cannot imitate translucent ink on a tinted fiber.

Weight and opacity

Thin or lightweight papers let the printing on the back show through, which affects light colors and large solids. A heavier sheet masks it. If both sides carry heavy ink, ask about show-through before choosing the weight.

CoatedUncoatedKraftColor vividnessFine detailDot gainSuits white inkneedRatings are general tendencies for illustration, not measurements.
Illustrative ratings of how coated, uncoated and kraft stocks tend to treat typical process color.

Finishes and coatings, and what they do to color

A finish changes how a sheet looks and feels after the ink is down. It also changes color, sometimes slightly and sometimes a lot. For a longer tour of the options, see Foil, Embossing and Spot UV: Premium Finishes and The Anatomy of a Premium Business Card. Here is the color angle.

Gloss

Gloss coatings reflect light in one direction, which deepens dark colors and raises contrast. Blacks look blacker, saturated colors look richer. The downside is glare: under strong light, a gloss surface bounces a reflection into your eye that washes out whatever is under it.

Matte

A matte finish scatters light in many directions. Darks look a little lighter and more muted, and the overall look is calmer and more modern. A matte coating can slightly lift very dark colors, so a rich black can seem more gray than the same black under gloss. Expect to see a small drop in color intensity compared to a gloss proof.

Matte lamination and soft touch

Laminate is a thin film bonded to the sheet. A matte laminate adds a quiet, even look and a scuff resistance that spot coatings lack. A soft touch laminate adds a velvety feel. Both tend to dull saturated colors and lower contrast a bit, and some tint the sheet very slightly. A common surprise is dark solids looking subtly grayed by the film. If a dark solid is a feature of the design, tell the printer, and look at a sample finished with the exact laminate.

Spot UV

Spot UV is a clear, glossy coating applied to chosen areas only. Against a matte background, it creates a striking glint on a logo or a pattern. Spot UV is specified in the file as a spot swatch on its own layer, which controls where the coating goes. It does not change the underlying color much, but it changes how that spot of color reads under light, and it needs registration that is a hair precise.

Foil

Foil is a thin metallic or pigmented film pressed onto the sheet with heat. It is not an ink. The color you get is the foil's own, which cannot be built from process inks and cannot be accurately previewed on a screen. A foil area is specified as a spot layer, the same way spot UV is. Fine detail and tiny type are risky, because foil does not like thin gaps.

Emboss and deboss

Raised or pressed shapes change how light falls across the surface. They do not change color directly, but they create shading, so the printed color under an emboss can look a little different at the edges. Align printed art and embossing carefully, or ask whether the emboss will be blind, with no ink.

Foil or spot UVSelective top effectLaminate or coatingChanges shine and depthPrinted inkProcess or spot colorPaper stockWhite point and texture
A finished card stacks several layers, and each one can nudge the color that reaches the eye.

Special inks: metallic, fluorescent and white

Process inks are translucent and limited. Some effects need an ink made for the purpose.

Metallic inks

A metallic ink contains fine metal flakes that reflect light, so the surface seems to shimmer as it moves. It is a spot ink, specified by name like any other. Printed metallics look different from foil: less mirror-like, more satin. They also look different depending on the stock, being brighter on coated and flatter on uncoated sheets.

Fluorescent inks

A fluorescent ink glows by turning invisible light into visible light, which lets it look brighter than the page. It reaches colors no process mix can match: neon pink, highlighter yellow, signal orange. It tends to fade faster than ordinary ink in strong sunlight, which matters for outdoor signage.

White ink

White ink is opaque, unlike the translucent process set, and it is how you get a white element on a dark or clear surface. It is used on kraft and colored stock, on clear materials and on dark apparel and promo items. Because it covers, it is often applied as a base layer under other colors, to make them bright on a dark sheet. That adds a pass, and a cost.

Simulating them when you cannot print them

Sometimes the effect is not available, the budget forbids it, or you are making a mockup. You can imitate each effect in artwork, and you should label the simulation clearly so nobody mistakes it for the real finish.

  • Metallic: a subtle gradient with bright and dark bands, in warm or cool gray with a hint of color.
  • Fluorescent: the closest bright process color, on a white background, accepting that it will look duller than the real thing.
  • White on dark: leave the area as paper by knocking out, if the stock is light, or flag it as a white ink layer if the stock is dark.

Never send a simulated gold gradient to a printer and expect foil. The file should say what you want, using named spot layers for real effects, and the mockup should be a separate, labelled file.

Real special inkProcess simulationLookReflects, glows orcoversFlat approximationSetupExtra plate or passNormal process runConsistencyHigh across jobsVaries with pressBest useWhere the effect is thepointMockups and tightbudgets
Real special inks and process simulations differ in what they can reproduce and what they cost.

Color on promo products and apparel

Everything so far assumed paper. Promotional products and apparel change the rules, because the surface is a mug, a bag, a pen barrel or a cotton shirt, and the imprint method sets how much color you can have. For a method by method guide, read Imprint Methods Explained. The color points are these.

Limited color counts

Many imprint methods work one color at a time. Each ink is a separate screen, pad or pass, and every added color adds setup. That is why promo quotes talk about the number of colors in a logo. A one color logo is the cheapest, a two or three color logo costs more, and a full color photographic image needs a method that can do it, such as a digital transfer or a full color print process.

For that reason, logos for promo use should be reduced to the fewest flat colors, with each defined as a spot color. Flat colors with crisp edges survive best. Fine gradients, shadows and tiny details usually do not.

Spot colors on products

Because promo work leans on single inks, spot colors are the norm. Name the ink exactly, and ask the decorator what they can match. On a material like glass, plastic, metal or fabric, the ink sits on a surface that does not behave like paper, so the match is judged on the item, not on a paper swatch. A color that looks right on a coated sheet can look quite different on a dark plastic barrel.

Dark and colored items

A dark shirt or a dark product swallows process inks the way kraft paper does. The usual solution is an underbase of opaque white ink beneath the color, or choosing an ink that is opaque to start with. Light colors need that base. Dark colors on a light item go on directly. Tell the decorator the item color when you quote, and expect a mockup.

Embroidery and thread colors

Embroidery does not use ink. It uses thread, in a set of fixed thread colors, and a logo is stitched in a limited palette. Color matching means choosing the thread that comes nearest to your brand color, not blending anything. Fine detail is limited by stitch size, and gradients cannot be stitched. A digitized version of the logo, prepared for stitching, is a separate file with its own thread list.

Things that change color on the product

  • Material sheen. Glossy plastic and metal look different from matte fabric.
  • Heat. Some methods use heat to cure the ink, and a few colors shift slightly.
  • Washing and wear. Apparel ink fades over time, and the method decides how fast.
  • Texture. A rough weave breaks up fine lines and soft edges.
One flatcolorSimplest andcheapestTwo or threespot colorsMore screens orpassesMany spotcolorsSetup growsquicklyFull colorimageNeeds a processcapable method
Each step up in imprint complexity adds colors, setup and the need to simplify the art.

Documenting brand color so it survives handoff

A brand color that lives only in one designer's head, or as one hex code in a slide, will drift. Every vendor makes their own guess, and six months later the red on the box does not match the red on the sign. The cure is a spec table that gives every medium its own value, kept in one place and sent with every order. The brand guidelines guide covers the wider document. Here is what color needs.

What each row of the table should hold

For every brand color, record:

  1. A name and a role, such as primary, accent or neutral.
  2. A web value, in the form used on screens.
  3. An RGB value for digital design tools.
  4. A CMYK recipe for process printing, with the profile it was built for.
  5. A named spot ink reference, if one exists, with coated and uncoated versions.
  6. Notes: where the color is allowed, minimum size, and the approved substitute when the original cannot be matched.
An example color spec table (values are placeholders, not real brand colors)
RoleScreen valueProcess CMYKSpot inkNotes
PrimaryHex value hereFour percentages hereNamed ink, coated and uncoatedLarge solids use spot where budget allows
AccentHex value hereFour percentages hereNone, process onlyNot for small text
Dark neutralHex value hereK only for text, rich recipe for solidsNot applicableNever mix the two recipes
Light neutralHex value hereLight tint, check the minimum dotNot applicablePaper may be used as the color

Be honest about what cannot match

Some screen colors have no process twin. Say so in the spec, name the closest printable value, and show it. A printed chip beats a number. When a vendor knows the approved substitute, they stop guessing and they stop sending versions for approval that nobody can judge.

Different values for different stocks

Record a version for coated and a version for uncoated, because one recipe looks different on each. If your brand lives on kraft or colored stock, add a note for them too, usually naming a spot ink and the white underlay to go with it.

Keep files and specs together

Put the spec in the same folder as the logo files. Name logo files with their color mode, such as screen, process and spot versions. When a reseller or agency passes artwork to a printer, the spec travels along, and the printer sees what the client intended. That is the simplest way to stop slow drift across vendors and reorders.

Hypothetical: a reorder two years later

Imagine a client orders signage from one vendor and cards from another, two years after the logo was first printed. If the only record is a hex code, each vendor converts it their own way and the two items disagree. If a spec table with a process recipe, a spot reference and a printed chip exists, both vendors work from the same page. This is a hypothetical scenario to illustrate the reasoning.

Primary roleScreen valuePrimary roleProcess recipePrimary roleSpot inkDark neutralText and rulesLight neutralPaper or tint
These swatches illustrate how one role in a brand system can carry several defined values, and are not real brand colors.

Proofing: soft, digital, hard and press check

A proof exists to show you what a screen preview cannot. There are four common levels. They cost different amounts and answer different questions.

Soft proof

A soft proof is a screen preview that uses the printer's output profile to imitate how the file will look in print. It is free, fast and useful for catching the big shifts, such as a gamut loss or an unexpected dark. It still depends on your display, so it is a hint and not a verdict.

Digital proof

A digital proof is a PDF the printer sends back, showing the layout as it will be produced: trim, bleed, text, and placement. It is an excellent way to confirm structure. It is not a reliable color check, because it is viewed on a screen, which brings us back to the start.

Hard proof

A hard proof is a physical print made on the actual press or on a device calibrated to match it. This is the only proof that shows color honestly before a full run. For a high value job, a strict brand color, or a first order on a new stock, it is the one to ask for.

Press check

At a press check, you stand at the press and approve sheets as they print. It is the tightest control available, and it is reserved for very color sensitive or high value work. On short runs run on digital presses, a press check is less common because the press is closer to a plotter that repeats the same file.

Proof levels compared
ProofShows color accuratelyShows layoutTypical use
Soft proofRoughly, depends on your displayYesCatching big shifts while designing
Digital proofNo, screen onlyYesApproving trim, bleed, text and placement
Hard proofYes, on the right stockYesBrand color, new stock, first order
Press checkYes, liveYesColor critical, high value runs

Lighting and viewing conditions

A proof looked at in the wrong light is a proof wasted. Different light sources give different results: warm bulbs tint everything yellow, cool office tubes push blue, and a window gives daylight that changes through the day. Printers use a standard viewing light, and the same idea works at your desk. Look at samples in neutral daylight or a daylight-balanced lamp, away from colored walls and clothing, and compare against the reference sample side by side.

A related point is metamerism, the odd fact that two colors can match under one light and differ under another. A fluorescent ceiling light and a sunny window can reveal that a match is really a coincidence. If a color has to hold up in several settings, check it in more than one.

Keep the approved sample

For work that will repeat, put the signed sample in a drawer. When a reorder arrives, lay it next to the new run. That one habit settles most color arguments, because it replaces memory and screens with a physical reference.

Soft proofCatch big color shiftsDigital proofConfirm layout and bleedHard proofJudge color on the stockPress checkApprove live sheets
Each proof level narrows the questions left open before a full run, and the cost rises as you go down.

Color variation across runs, and how to approve a proof

Even a perfect job on a good press will not match the next run to the last decimal. That is not a failure. It is the nature of a physical process, and knowing what is normal keeps you from fighting it.

Why runs differ

Ink batches vary a little. Paper lots vary a little. Humidity and temperature change how ink behaves and how paper takes it. A press warms up and settles during a run, so the first sheets and the last can differ faintly. Different machines, even of the same model, have their own character. A reorder months later meets a different ink batch, a different operator and a different day. Each factor is small. Together they set a band inside which results are considered the same job.

What is normal

Printers work to a tolerance, a range of acceptable difference from the approved target, and many measure it with an instrument and a stated number. You do not have to speak that language, but you should ask what tolerance applies, and whether the printer works to a measured target or to the approved sample. For a casual eye, a normal shift is small: when you lay two sheets side by side under good light, you might see a slight difference, and when you view them apart, you would not. A shift you can spot across the room, or one that changes the feel of a brand color, is outside the band and worth raising.

Digital presses repeat very closely within a run but still shift across days and machines. Offset presses are tuned live by the operator, so consistency depends on skill and on a measured target. Spot inks reduce variation for brand colors, since the ink recipe is fixed, but they are still mixed by people and applied on a press.

Ways to keep reorders close

  • Send the same file, not a rebuilt one.
  • Keep the approved sample and send a photo, or the sample itself when practical.
  • Use the same stock, and say so on the order.
  • Record the output profile and spot ink names with the job.
  • Ask for the same printer and press type where you can.
IdenticalClearly differentInvisibleNormalSide by sideonlyUsually withintoleranceVisible apartRaise itObviousLikely an error
Illustration of the range of variation between runs, from invisible to worth a conversation.

How to approve a proof

Approving a proof is a decision with consequences, since your signature usually means the printer is not responsible for what you accepted. Do it with care.

  1. Check the version. Make sure the proof matches the file you meant to send, not an older one.
  2. Use proper light. Neutral daylight or a daylight lamp, not warm bulbs.
  3. Look at color against a reference. Brand chip, previous print or approved sample, side by side.
  4. Check the stock. The proof should be on the stock ordered, or you must be told how it differs.
  5. Read every word. Spelling, numbers, phone numbers and addresses cause more reprints than color does.
  6. Check edges and bleed. Make sure nothing important sits too close to the trim.
  7. Review finishes. Where foil, spot UV or emboss go, and whether they land on the right elements.
  8. Write down your notes. Ask for a revised proof when you request a change, and do not approve on a promise.

If something looks off, say what you see in plain terms, such as "the blue looks purple next to the chip," and avoid prescribing numbers. A printer can often adjust more effectively when given the symptom and the reference.

Right file versionMatches the currentartworkViewed in neutrallightNot under warm bulbsCompared with areferenceChip or earlier sampleStock confirmedOr the difference is knownText proofreadNumbers and spellingFinishes placedcorrectlyFoil, spot UV, emboss
A proof is ready to sign only when these checks have a clear answer.

What the artwork proofer flags and how to respond

When you upload a file to Inkgility through upload your design, the artwork proofer runs preflight checks and shows each one as a pass, a warning or an error. This section describes those checks as they exist, and what to do about each. It does not promise that a passing file will print exactly as you imagine. A pass means the file has no known problem of that type.

Resolution

For raster images, the proofer works out the effective resolution at print size. At 300 effective DPI or above, the check passes. Below 300 it warns that the image may not look sharp. Below 150 it reports an error, because the print will look visibly blurry. Vector artwork passes, since it scales to any size.

Response: use a larger original, or reduce the print size of that image. Do not upscale in software and expect detail to appear. If only a photo is the problem, replace that photo and keep the vector parts.

Color space

A CMYK file passes, since colors print as designed. A grayscale file also passes. An RGB file draws a warning, because it will be converted to CMYK at print and bright blues, greens and oranges may shift darker.

Response: convert the file yourself as described earlier and look at the result, so you control the shift. Then re-upload.

Trim and bleed match

The proofer compares the artwork's size to the product's trim and bleed size. A file built to the full bleed size passes. A file built to the exact cut size draws a warning, because it has no bleed, and other sizes are flagged too. A file whose proportions match the print size passes that comparison.

Response: extend background art and images to the bleed edge, using the product template as a guide. If you scaled the file, rebuild it at the right size rather than stretching.

Safe zone

When a product has both a bleed and a safe inset, and the artwork stops at the cut line, the proofer warns that nothing is left to cut into. Key content should stay a set distance inside the edge. If the artwork extends past the cut line, it passes with a reminder to keep key content inside the safe zone.

Response: pull text and logos inward, and extend only background elements to the bleed.

Fonts

Some file types can contain live text, and the proofer warns that fonts may not be outlined. For PDFs, it reports whether live text has embedded fonts, passing when text is embedded or outlined, and warning when fonts do not appear to be embedded.

Response: convert text to outlines, or export with fonts embedded, then upload again.

Overprint

Overprint settings cannot be verified automatically from an uploaded file, so the proofer raises a recommendation and prepress reviews them before production. This is a prompt to check your own file first.

Response: open your separations or attributes preview and look for objects set to overprint, especially white or light colored ones.

Page count

A file with several pages draws a warning, because only page 1 is used for that face of the product.

Response: upload each face as its own file.

Proofer checks and the usual response
CheckPassWarning or errorUsual fix
Resolution300 effective DPI or more, or vectorWarning under 300, error under 150Larger source or smaller print size
Color spaceCMYK or grayRGB warns of a conversion shiftConvert and review
Trim and bleedBuilt to the bleed sizeBuilt to cut size or another sizeRebuild with bleed
Safe zoneArt extends past the cut lineArt ends at the cut lineMove key content inward
FontsOutlined or embeddedLive fonts not embeddedOutline or embed
OverprintNo overprint possible in the file typeReview recommendedCheck separations
Page countSingle pageMore than one pageOne file per face
1PassNo known problem of that type2WarningProbably fine, worth a look3ErrorFix before it prints
The proofer gives each upload a short report, and warnings need your acknowledgment before production.

Troubleshooting guide

When a print disappoints, work from the symptom to the likely cause. Most color problems come from a short list.

Colors look dull or flat

Likely causes: an RGB file converted at the last minute, bright colors outside the process range, a different stock from the proof, a matte finish or laminate over the top. Fix: convert deliberately and review, consider a spot ink for the key color, and check the stock and finish against the proof.

Dark areas look muddy

Likely causes: total ink too high, a rich black recipe too heavy, uncoated stock spreading dots, or a dark photo converted without adjustment. Fix: check total ink, ask for the printer's rich black recipe, and lighten the shadows slightly before conversion.

Banding in gradients or soft backgrounds

Likely causes: a gentle gradient across a large area, a low-resolution or flattened gradient, a light end that drops under the minimum dot. Fix: add a very light noise, increase the range of the blend, or replace the gradient with a flat color or a spot ink.

Colors differ between two printers

Likely causes: different presses, profiles and stocks, no shared spec, and different tolerances. Fix: give both printers the same file, profile name and spec table, ask each for a hard proof on the same stock, and compare to one physical reference.

Small text looks fuzzy or has colored fringes

Likely causes: small type built from several inks, misregistration, a pure RGB black converted to four colors. Fix: set small text to K only, enlarge very thin type, and check that no tint is applied.

A color changed after export

Likely causes: flattening transparency, spot colors converted to process, a different profile applied during export. Fix: reopen the exported PDF, look at its color information and separations, and adjust export settings.

White elements are missing

Likely causes: white set to overprint, white on a dark stock with no white ink, or a white object that is really transparent. Fix: turn off overprint for white, and request an opaque white ink pass where needed.

Edges show a white sliver

Likely causes: no bleed, trimming drift, or plates out of register. Fix: extend art into the bleed and keep key content inside the safe zone.

What looks wrong on the print?Color is dull or shiftedCheck conversion,stock and finishDark areas are muddyCheck total inkand black recipeText is fuzzySet small text toK only
Start with the symptom you see and follow the branch to the most likely first fix.

A pre press checklist for color

Run through this list before you send a file. It takes a few minutes, and it catches the problems that cause most reprints. Check each point on the exported file, not only on the working file.

Color

  1. The document mode matches the plan: process for photos, with spot swatches only where a spot ink is meant.
  2. The output profile is the one your printer asked for.
  3. Every brand color is a named swatch, with spot inks named exactly, coated or uncoated.
  4. Gamut warning reviewed, and each flagged color accepted, adjusted or moved to a spot ink.
  5. Black text and thin rules are K only. Large solids use the agreed rich black recipe.
  6. Total ink is within the limit on dark photos and solids.
  7. No object is set to overprint by accident, especially white and light colors.

Artwork

  1. Photos are at least 300 effective DPI at their print size.
  2. Gradients are checked for banding, and the light ends stay above the minimum dot.
  3. Transparency effects are flattened in a preview and look right.
  4. Logos are vector, with defined swatches for each color mode.

Layout and finishing

  1. Bleed is built in, and key content sits inside the safe zone.
  2. Fonts are outlined or embedded.
  3. Foil, spot UV and emboss are on their own layers with named spot swatches.
  4. Each face of the product is its own page or file, as the product requires.

Proof and approval

  1. A proof level suitable to the job was requested, and the stock matches.
  2. The approved sample is stored for the reorder.
  3. The color spec table is sent with the file.

Before an upload, the artwork upload tool will flag several of these for you, and the handoff guide covers the file level mistakes that cause reprints.

Set upConvertProofApproveRecordColor loop
Color control repeats with every job: set up, convert, proof, approve, then record for the next order.

Glossary of color terms

Short definitions of the terms used above, in plain language.

  • Additive color: color made by adding light, as on a screen.
  • Black point compensation: a setting that maps the darkest tones of the source to the darkest the destination can print.
  • Bleed: artwork that extends past the cut line so trimming never leaves a white edge.
  • CMYK: cyan, magenta, yellow and black, the four process inks.
  • Dot gain: the spread of halftone dots as ink lands on paper, making tones look darker.
  • Gamut: the full range of colors a device or process can reproduce.
  • Halftone: a pattern of dots whose size sets how strong a tone looks.
  • ICC profile: a data file describing how a device or output turns numbers into color.
  • K only: black printed from the black plate alone, with no other inks.
  • Knockout: an object that removes the ink beneath it so its own color prints clean.
  • Metamerism: two colors that match under one light and differ under another.
  • Misregistration: slight drift between plates that can leave gaps or fringes.
  • Overprint: an object printing on top of what lies beneath, so inks stack.
  • Out of gamut: a color that a given process cannot reproduce.
  • Process color: color built from overlapping dots of the four inks.
  • Registration black: a swatch with every ink at full strength, only for marks.
  • Rendering intent: the rule a conversion uses for colors the destination cannot hold.
  • Rich black: black with other inks beneath it, for deeper large solids.
  • Rosette: the small flower-like pattern formed by the four overlapping dot screens.
  • RGB: red, green and blue light, the system of screens.
  • sRGB: a common, modest color space used for the web and ordinary displays.
  • Spot color: a single premixed ink applied on its own plate or pass.
  • Subtractive color: color made as ink absorbs light from a reflecting surface.
  • Tint: a lighter shade made with a smaller halftone dot of the same ink.
  • Total ink coverage: the sum of all ink percentages at one point.
  • Trapping: a small overlap between neighbouring colors so gaps do not show.
PrintcolorLight and gamutInks and dotsBlack and inklimitPaper and finishProofing
Nearly every term in color for print connects back to one of these central ideas.

Frequently asked questions

Should I design in CMYK or RGB?

For a printed piece with a fixed color target, work in CMYK using the profile your printer asks for, so you see the real limits while you design. Photos can be edited in RGB, where they keep their full range, and converted once near the end. If the piece lives on screens and on paper, keep both sets of values in your brand specification and treat the screen version as the draft. Whatever you choose, convert on purpose and look at the result before sending the file, because an automatic conversion at the last minute is the most common source of surprise.

Why does my print look duller than my monitor?

A monitor emits light, so it can show brighter and more saturated colors than ink on paper can reflect. Bright blues, greens and oranges are the usual victims, because they fall outside the range of the four process inks and get moved to the nearest printable color during conversion. Paper, laminate and lighting can add to the effect. A calibrated display, a soft proof with the printer's profile, and a printed sample on the real stock will show you the difference before the full run.

What is the difference between a spot ink and CMYK?

CMYK builds a color from overlapping dots of four inks, so the result depends on the press, the paper and the profile. A spot ink is a single color mixed ahead of time and printed on its own, so it stays steady from job to job and can reach colors the process set cannot, including metallic and fluorescent ones. The trade is cost, since spot inks often need an extra plate or pass, and spot ink is not suited to photographs.

Does paper stock change color?

Yes, a lot. Coated stock keeps ink on the surface, so colors look cleaner, brighter and sharper. Uncoated stock absorbs ink and spreads dots, so colors look softer, flatter and a little darker. Kraft and tinted stocks show through the translucent inks and change every color on the page, and white elements need an opaque white ink. The same file will look different on each, so judge color on a printed sample of the stock you actually ordered.

What is rich black and when should I use it?

Rich black is black with some cyan, magenta and yellow printed under it, which makes large solid areas look deeper and more solid than the black plate alone. Use it for big backgrounds and large headlines, and ask your printer for their preferred recipe instead of guessing. Keep small text and thin lines in K only, black from the black plate with no other inks, because four plates drifting slightly out of register will make small type look fuzzy.

Why does the same file print differently on a reorder?

A press is a physical process, so ink batches, paper lots, humidity, the operator and the machine all vary a little between runs. Printers work inside a tolerance band, and small differences you only see side by side are normal. To keep reorders close, send the same file, name the same stock, record the profile and spot ink names, and keep the approved sample to compare against. A shift visible from across the room is worth raising.

Do I need a hard proof for every job?

Not for every job. A soft proof and a careful read of a digital proof are often enough for a simple flyer. A hard proof, a physical print on the right stock, is worth requesting when a brand color is strict, when you are using a new stock or finish, or when it is a first order that will be repeated. A press check is reserved for color critical or high value runs. Match the proof level to what a mistake would cost.

How do I stop small black text looking fuzzy?

Set small text, thin rules and barcodes to black from the black plate only, with zero percent of the other inks. Fuzzy edges almost always mean the text was built from several inks that drifted slightly out of register, or a pure RGB black was converted to a four ink mix. Check black text after any conversion, enlarge very thin type, and keep rich black for large solid areas only.

What does the Inkgility proofer warn about for color?

The proofer checks color space, among other things. A CMYK file passes, a grayscale file passes, and an RGB file gets a warning because it will be converted to CMYK at print and bright blues, greens and oranges may shift darker. It also flags low resolution, trim and bleed mismatches, safe zone risk, fonts that are not outlined or embedded, page count, and overprint, which prepress reviews because it cannot be verified automatically from the file.

Can I match a brand color exactly on every product?

Not in every medium, and an honest guideline admits it. Paper, laminate, fabric, plastic and thread each treat color differently, and some screen colors have no process equivalent. What you can do is document each color with a screen value, a process recipe, a named spot ink where one exists, and an approved substitute, then send that table with every order. A printed chip beats a number as a reference.

Check your artwork before it prints

Upload your design and the proofer flags color space, resolution, bleed and fonts before production. Start from a template or bring your own file.

Upload your design

Reselling print to your own clients? Apply for a trade tier